• Motorola VIP2250 dvr keeps rebooting/freezing My dvr keeps freezing/rebooting. If I turn the tv on, it either freezes and I cant make it change channels or anything else or if I am able to change the channel, it then reboots.
• ARRIS Consumer Support Model - VIP5602EW. Coronavirus (COVID-19) Disruption Our Call Center is experiencing a high number of calls due to the COVID-19 situation.
• Page 1 ARRIS DVR Receiver Installation Manual VIP2250 For use with your AT&T U-verse TV Service.; Page 2 VIP2250 U-verse DVR Receiver Installation Manual.; Page 3 This manual includes the manufacturer’s recommended safeguards and all the information needed to connect your receiver to both your in-home IP network and your entertainment system. The safety and installation information was.

1. Vip2250 Receiver
2. Motorola Vip2250 Specifications

Motorola VIP 1003 User Manual. Full screen Standard. Connecting to power. When all other cables are connected, connect the power cord to. Page 1 ARRIS DVR Receiver Installation Manual VIP2250 For use with your AT&T U-verse TV Service. Page 2 VIP2250 U-verse DVR Receiver Installation Manual. Page 3 This manual includes the manufacturer’s recommended safeguards and all the information needed to connect your receiver to both your in-home IP network and your entertainment system.

Vip2250 Receiver

• Before doing this, if your dvr keeps rebooting and it's happening more frequently, make sure air vents are not obstructed and device has good air-circulation. The fan/air-intake is located underneath the DVR near the front. Check to make sure it is not blocked (papers underneath being sucked up blocking air-flow or covered in lint/dust). I suggest unplugging unit, taking it outside and blowing out fan-intake are using compressed air. These devices sit working for a long time and can suck up a lot of dust (especially in an environment with pets, smoking, or windows kept open). I suggest an annual clean out as above.

Warning!The reset information below should only be done at your own risk!! In some cases, it could disable your DVR or cable features, requiring a service call or replacement. It's even possible you could be fined if the DVR is damaged.

DVR HDD Reset[edit]

This will wipe out all of your recordings, all scheduled recordings, all series recordings (your series priority list), and all manual recordings!! Write down everything you can before you do this!

1. While the DVR is on, push power to turn it off (by pressing CABLE, POWER on your remote control) or by pushing power on your set-top box.
2. Immediately press OK on your remote or SELECT on your set-top box. Push it twice. A diagnostics page -- black text on a white background -- will appear on your television screen (make sure television is on).
3. While on this screen, perform the following key sequence with your remote:

Press the circular counter-clockwise arrow (REPLAY on some remotes) 2 times

Press the MyDVR (LIST on some remotes) button 3 times

Press the live button 2 times

1. 'Clr' will appear on the LED display.
2. Press OK/SELECT to proceed with the reset. The STB should now reformat the hard drive and then perform an STB reset and begin to reload your cable settings and time settings from the head end. It will then begin to populate the guide data over the next two to 24 hours.

(On some systems, the button press pattern may be 1-3-1, not 2-3-2 as above. This is true for all the STBs for Shaw Cable. For the DCH3416, the pattern is 1-3-2.)

DVR Authorization and Factory Full Reset[edit]

WARNING: This will download and reinstall the DVR firmware and software. This should not erase your user settings or delete your stored recordings on the DVR. This is not guaranteed, proceed at your own risk.

1. Unplug the power cord from the DVR.
2. On the front of the DVR, press & hold the POWER & MENU buttons while plugging the power cord back into the DVR. The display should now read 'boot'.
3. Release the POWER & MENU buttons.
4. Press the UP or DOWN ARROW buttons on the DVR (not the remote) until you see 'n dl' on the display.
5. Press the OK/SELECT on the DVR to begin authorization & downloading of software, STB/DVR firmware from your cable headend. It could take up to 20 minutes to download the firmware, the software could take up to 2 hours depending on what software your cable provider has. You should see 'n dl' in the LED display with a line moving in a square.
6. After it completes this download the DVR will then reboot and begin to download the time settings for the clock along with your cable account info and settings. After this is done, it will begin to populate the Guide info. It could take up to 24 hours to fill in all two weeks of information. Depending on your location, environmental variables and number of users with digital cable or cable Internet, the download can take up to twice as long.
7. If the display on your Motorola DVR displays only the number 0 after performing this process, it is in need of a reset by your cable provider. Call them and ask them to reset your box.

Supported Models[edit]

• This procedure is not confirmed to work on the newer DCH-series DVR's.
• It is confirmed to be working on Time Warner Cable DCX-series DVRs.
• It is confirmed to be working on Insight and Cox Communications model 6416 III, Cox Communications model DCT3416 I, and Comcast Cable model 3412 I.
• Did not work on a Charter/Spectrum DCH3416; only options were 'boot', 'disp' and 'diag'.

Remote Control Resets[edit]

Information on resetting the remote control can be found at Programming the RemoteResets

Motorola Vip2250 Specifications